What Are the Advantages of V-Mixer Performance?

V-type mixer series products are high-efficiency asymmetric mixers, which are suitable for mixing powder or granular materials in chemical, food, pharmaceutical, feed, ceramics, metallurgy, and other industries. The structure of the machine is reasonable, simple, hermetically sealed, easy to feed in and out. (Manual or vacuum feeding) The cylinder is made of stainless steel, which is easy to clean. It is one of the basic equipment of the enterprise.

It is suitable for the mixing of powders and granules with good fluidity and small physical properties, and for materials with low mixing degree and short mixing time. Because the materials in the V-type mixing container flow smoothly, the original shape of the material will not be damaged. Therefore, the V-type a mixer is also suitable for the mixing of fragile and abrasion able granular materials, or the mixing of finer powders, blocks, and materials containing a certain amount of moisture. It is widely used in the pharmaceutical, chemical, food and other industries.

Precautions during use: 1. A dry run test should be performed before use. Before the test, the solidity of all the connections of the horizontal V Shape Dry Powder Mixer should be checked, the amount of lubricating oil in the reducer and the integrity of electrical equipment And then close the main switch, turn on the power, and perform a dry run test. 2. Installation: Place the machine stably, install the machine feet, and flatten it so that the machine can run freely. 3. Before use, fill up the oil to be refueled, and then perform no-load the operation, check whether the fasteners are loose, whether the electrical is normal, whether the machine is operating normally, and if there is abnormality, repair and debug. 4. Turn the feeding port to the top, open the feeding cap for feeding, and the feeding amount should not exceed the specified volume, then close the feeding cap tightly and start the machine to run. If an abnormality is found on the way, it must be stopped for inspection.

The use method of the V-type mixer is to open the feeding port of the mixer and check whether the discharge port is closed when the belt is running and put a specified amount of material into the V-type hopper according to the process control requirements. After the feeding is completed, in order to prevent the material from flowing out during mixing, the feeding port should be closed and locked. Next is the working time of the machine. Turn on the power button, rotate the stop button to the left, start the reverse button of the mixer, and adjust the motor speed to 600r / min for mixing within the specified speed of the process. After the mixture reaches the time specified in the process, stop the machine by adjusting the motor speed button. When the machine is stopped, the discharge opening of the mixer should be directly facing the ground, and adjust the motor speed button to 0 positions. The V-type mixer will stop the button Turn right to cut off the power. The last is discharging: Open the feeding port of the V-type mixer, and use the specified container to load at the discharging port until the material in the hopper is discharged.

There are still a lot of things we need to pay attention to during the installation and use of the V-type mixer, which will help us maintain the V-type mixer and increase its service life. 1. Installation: Place the machine stably, install the machine feet, and flatten it so that the machine can run freely. 2. Before use, refill the oil to be refueled, and then run it at no load, check whether the fasteners are loose, whether the electrical is normal, and whether the machine is operating normally. If there is any abnormality, repair and debug. 3. Turn the feeding port to the top, open the feeding cap for feeding, and the feeding amount should not exceed the specified volume. Then close the feeding cap and start the machine to run. If an abnormality is found on the way, it must be shut down and inspected. 4. When changing the variety, the inside and outside of the hopper must be rinsed clean. It is suitable for mixing powder or granular materials in chemical, food, medicine, feed, ceramics, metallurgy, and other industries. The structure of the machine is reasonable, simple, hermetically closed, easy to feed in and out. (Manual or vacuum feeding) The cylinder is made of stainless steel, which is easy to clean. It is one of the basic equipment commonly used in enterprises.

Our company also has Vacuum Dryer Industrial, Powder Mixer Mixing Machin, etc. If you are interested, you can choose to contact us.

V-shaped mixer mixing production line